C1100 will not power on
Hi all,I have a C1100 which has been running for a few years now without any problems. Suddenly the server lost power and will no longer boot up. I replaced the power supply thinking that it might have...
View ArticleAdd drive to PERC6/6i virtual disk
I have a server with a PERC6i controller. There are 8 bays in the server. Five of these bays have 450GB drives and 1 large RAID-5 virtual disk has been created. The 450GB drives currently installed...
View ArticleCable for T320 8x3.5 to Perc H710
I have a T320 with the 8x3.5 hot-swappable backplane for SAS drives. I ordered a Perc H710 (p/n 342-4203) to replace the H310. The existing SAS cable has the wrong connectors for the H710.I chatted...
View ArticleESXi 5.5 Hypervisor ISO for Dell R710
Hi All,I need to Install ESXi 5.5 update 2 on My new Dell R710 server.I am not sure is there any customised OS or not.If Available , Please help me how can and from where I can download the...
View ArticleDell PowerEdge R620 Server Rollback to Factory Default Settings with Original...
I am having Dell PowerEdge R620 Series server. We have installed Window Server 2012 R2 Data Center edition in this server.Recently I have updated below firmware in the server & now I want to...
View ArticleR730XD H730P - F/W in in Fault State
When booting up, I get the following message from the PERC Controller:F/W is in Fault State - MFI Register State 0xF0010000Adapter at Baseport is not respondingNo AdapterWe use a bunch of SSD's.Any...
View ArticleIssues with PS-3, PS-4 on Dell PE 1855 Blade System
Hello I connected all power cables to PS-1, PS-2, PS-3 and PS-4.. but only two Power Supplies - become ON. PS-3 and PS-4 showing : Present - OFFI tried shutdown chassis and boot it UP again, and then...
View ArticleFiber card not showing in firmware Inventory
I have two M620 blades in a 1000e chassis that has QLogic fiber cards that show up in the hardware inventory, but not the firmware inventory. I have eight other blades in that chassis that they show...
View ArticleCMC web interface access lost, requires RACRESET, inconsistent, but recurring
Under the CMC 4.5, we were able to reliably access CMC via the web interface for ~3 months. In January, we added externally signed certificates to the CMC (required by parent organization). We updated...
View ArticleClik here to view.
Dell r630 with Intel® Ethernet Converged Network Adapters X710
I have a server (r630)with an onboard intel X710 which is a converged adapter (2 copper and 2 sfp ports) When I boot the server I only see the 2 copper nics and not the SFP connected nics.When i check...
View ArticleDell Poweredge T410 memory upgrade
Hello everyone,Lately I decided to upgrade my server's memory to 28GB.I just tried to put it in my server and it gave me a warning that the memory configuration was not supported.I started to search on...
View ArticleRAID 1 Rebuild
I have a PowerEdge T710 with a PERC 6 controller running a RAID 1 configuration. The hard drive 0 is flashing amber so I am going to replace the drive with one that I purchased from Dell. How do I...
View ArticleSetting up M630 (VRTX) SPERC 8 shared disks on Win2012 R2 Std
HelloI have a 4 blade VRTX with the SPERC 8, I used the driver from this link:http://www.dell.com/support/home/us/en/19/Drivers/DriversDetails?driverId=0P5XVI was looking to this...
View ArticleT420 Power Supply Firmware Update not Working
I have a T420 server and it keep tell me to update the PSU Firmware and when I do it it does not upgrade.I have updated using dell lifecycle manager and after the reboot it say it has not updatedI have...
View ArticleBroken USC for R310
Main ProblemI have a PowerEdge R310 with only the BMC (no DRAC). From within Windows, I updated the Unified Server Configurator (USC) to newer versions offered on Dell's support page. When I reboot...
View ArticlePE R630, new battery detected.
the server sent the following message.Severity: Informational, Category: Storage, MessageID: CTL1, Message: Controller event log: Controller event log: Integrated RAID Controller 1 New Battery...
View ArticleRAID 1 Rebuild
I have a PowerEdge T710 with a PERC 6 controller running a RAID 1 configuration. The hard drive 0 is flashing amber so I am going to replace the drive with one that I purchased from Dell. How do I...
View ArticleiDRAC with Lifecycle Controller 2.10.10.10 on PowerEdge T430
Anybody getting a problem with the system board fan running 100% (4800RPM) after flashing this firmware. Getting the same issue on any T430 I flash. Flashing the version before this release returns the...
View ArticleR730XD H730P - F/W in in Fault State
When booting up, I get the following message from the PERC Controller:F/W is in Fault State - MFI Register State 0xF0010000Adapter at Baseport is not respondingNo AdapterWe use a bunch of SSD's.Any...
View ArticleC6100 server BSOD
I'm trying to track down why this server is experiencing blue screens.I see the following errors in the event log:Error Event ID 6008 "The previous system shutdown at 4:21:28 AM on 6/9/2015 was...
View Article